Energy saving Wood chipdryer machine
Wood chip dryer machine use range
Wood chip dryer machine widely used in straw press briquettes fuel,
charcoal machinery, wood chip granule fuel, sawdust press blocks,
farming and animal husbandry engineering industry. Such as corn
straw drying, soybean straw drying, cotton straw drying, wheat
straw drying, sorghum straw drying, wood chips drying, wood shaving
drying, sawdust drying, ginkgo leaf drying, mulberry leaves drying
and the agricultural cellulosic-based material's drying. etc.
which use screw conveyor put the powder wet sawdust into the dry
tube continuously. In the conveying and dispersed of high speed hot
air, to make the water in the wet material evaporation, to get the
powder or granular dry product. It mainly is composed by air
heater, feeder, airflow drying pipe, cyclone separator, fan etc.
Wood chip dryer machine performance characteristics
1.wood chip dryer machine has great handling ability,fuel
consumption less,low drying cost.
2.High temperature resistant,can use high temperature and hot air
to dry materials rapidly.
3.Its expanded ability is strong,design considered production
surplus,even if yield increased slightly, also need not changing
4.It adopts“self-aligning type”tug structure,tug match up well with
rolling ring,and greatly reduce wear and power consumption.
5.Special designed catch wheel structure,greatly reduces tilt of
equipment which work provides the horizontal thrust.
7.Dry and moisture control, minimum up to 5% or less,meet material
Wood chip dryer machine operating principle
1.A rolling cylinder which slightly inclines is main part of a 3
drum dryer.wet materials are fed from the higher end of the cylinder when the
heating media are being sent through the lower end.
2.Under influence of the gravity,wet materials flow downwards to
the lower end and contact the heating media directly or indirectly.
3.There is a stirring plate on the inner wall of the cylinder to
stir materials continuously and make them have a full contact with
4.Having been dried, the materials are conveyed to discharge end.
Wood chip dryer machine structure
1.It is formed by rotary body, lifting blade, driving device,
supporting device and sealing ring.
2.Wood chip dryer machineis mainly composed of shell, back and forth supporting wheel,
feeding and discharging unit and gear cap.
3.The accessories which are not in scope of this machine include
firebox, feeding and discharging equipment, dust catcher, etc.
1.It mainly consists of rotor, shed plate, transmission device,
support device, seal ring, and other spare parts.
2.Wood chip dryermachine has the advantages of reasonable structure, excellent
manufacture, high output, low energy consumption, convenient
operation and so on.
3.It is applicable for particle materials, and is also applicable
for paste and viscous materials which are mingled with particle
materials, or materials whose water content is high.
4.It has advantages of large production volume, wide application
range, small flow resistance, large adjustable range, and
convenient operation, etc.
As rawmaterial is sticky,it is divided into several section for
1.Transmission section. Wet coal slime enters this section, then
gets full contact with high temperature air, moisture inside gets
vapourized. With lifting boards elevate and scatter materials
repeatedly, wet coal slime is conveyed to next section.
2.Cleaning section. When materials fall down, they are easy to
stick on inner wall of cylinder. During this process, cleaning
device breaks the clumps.This spreads the surface area of heat
exchange and improves heat efficiency.
3.Lifting boards section. Wet coal slime is loose and of low
moisture content that meet requirement.
4.Discharging section. No lifting boards in this area. Materials
roll to outlet.The whole drying process is completed.
Wet materials, first scattered via special feeding scattering
device,then wet materials is sent to the feeding machine by
band-type feeder, and then wet materials is conveyed/delivered into
raw materials drum dryer roller by feeding machine,materials in
stirring function of shoveling plates which are equispaced in
drying roller,homodisperse and fully contact with hot air, to
achieve the purpose of heat transfer and mass transfer.rawmaterial
after drying in the end of roller discharge finished products from
the star-shape discharger,the belt discharging machine output the
dried products, and that complete drying process.
Main technical parameters for your reference
|Specification(Diameter*Length)(m)||Shell cubage(m3)||Capacity(t/h)||Installation obliquity(%)||Highest inlet air temperature(°c)||Main motor(kw)|
|Φ2.4*14||63.3||13.5-16.9||<;;;;span style="line-height: 24px; font-family: 'times new